1) these are stress ratngs. exposure of devices to any of these conditons may adversely afect long-term reliability. 2) (1.5mm from case 10sec max.) 3) all specifcatons typical at ta= 25c, nominal input voltage and full load unless otherwise specifed. 4) the informaton and specifcaton contained in this data sheet are believed to be correct at tme of publicaton. however rsg accepts no responsibility for consequences arising from printng errors or inaccuracies. specifcatons are subject to change without notce. dc/dc-converter rs7-s10/d10 1.0w unregulated single & dual output ? 7 pin sil package ? 6000vdc high isolaton ? physical clearance of isolaton barrier 2.5mm ? long term short circuit protecton ? low ripple and noise ? efciency up to 81% ? operatng temperature range -40 ~ +85c ? non conductve black plastc case output specification voltage accuracy: 3% line regulaton: 1.2%/ per 1% vin change max. load regulation: from 10% to 100% load: 10% short circuit protecton : indefnite (automatc recovery) ripple noise (20mhz bandwidth): 200mv pk-pk temperature coefcient: 0.03%/c capacitor load: see table input specifications voltage range: 10% max. max. input current: see table no-load/full-load input current: see table input filter: capacitors input refected ripple current : 20ma rms (rms thru 12uh inductor , 5hz to 20mhz) general specifications efciency: see table i/o isolaton voltage (60sec): 6000vdc i/o isolaton capacitance: 10pf typ. i/o isolaton resistance: 1000m ohm, min switching frequency: 20khz - 50khz humidity: 95% rel h reliability calculated mtbf : >2.39mhrs (mil-hdbk-217 f) safety standard: (designed to meet): iec 60950-1 environmental specification operatng temperature range: -40c ~+85c (see deratng curve) maximum case temperature: 100c storage temperature : -40c ~+125c cooling : nature convecton physical specifications: case material: epoxy encapsulated (ul94v-0 rated) clearance distance inp./outp. 2.5mm pin material: 0.5mm alloy42 solder-coated weight case- sip: 4.2g, typ. potng material: epoxy (ul94v-0 rated) dimmension sip: 0.77 x 0.39 x 0.49 absolute maximum ratings (1) input surge voltage (100ms)/ 5v models: 7vdc max 12v models: 15vdc max 15v models: 18vdc max 24v models: 28vdc max soldering temperature: 260c max. emc specifications (2) radiated-/conducted emissions: en55022 class b see emi filter esd: iec 61000-4-2 perf.criteria a rs: iec 61000-4-3 perf.criteria a eft: iec 61000-4-4 perf.criteria a surge: iec 61000-4-5 perf.criteria a cs: iec 61000-4-6 perf.criteria a pfmf iec 61000-4-8 perf.criteria a dc/dc-converter 1.0w unregulated single & dual output we energize electronics! an acal group company we energize electronics! rsg electronic components gmbh ? sprendlinger ldst. 115 ? 63069 offenbach ?+49 69-984047-0 ? rsg-electronic.de page 1 (3) stand juni 2016 rev 01
2 vl - 1w unregulated single & dual output model selection guide part number structure 50% 25% 75% 100% output power -40 -20 0 20 40 60 80 100 120 ambient temperature( ) derating curve 85 s.o.a. vl - 12 05 ss h6 isolation h6 - 6k vdc series name output type ss - single output s - dual output nominal output v oltage 3r3 - 3.3v 5 - 5v 9 - 9v 12 - 12v 15 - 15v input voltage range 5 - 5v 9 - 9v 12 - 12v 15 - 15v 24 - 24v model number input voltage range (vdc) voltage(vdc) output r s 7 - x x 0 3 s 10a 6 r s 7 - x x 0 5s 10a6 r s 7 - x x 0 9s 10a6 r s 7 - x x 1 2s 10a6 r s 7 - x x 1 5s 10a6 r s 7 - x x 0 3d 10a6 r s 7 - x x 0 5 d 10a6 r s 7 - x x 0 9 d 10a6 r s 7 - x x 1 2 d 10a6 r s 7 - x x 1 5 d 10a6 5, 9, 12, 15, 24 5, 9, 12, 15, 24 5, 9, 12, 15, 24 5, 9, 12, 15, 24 5, 9, 12, 15, 24 5, 9, 12, 15, 24 5, 9, 12, 15, 24 5, 9, 12, 15, 24 5, 9, 12, 15, 24 5, 9, 12, 15, 24 3.3 5 9 12 15 3.3 5 9 12 15 303 200 111. 1 83.3 66.7 151.5 100 55.6 41.7 33.3 69 - 75 70 - 77 70 - 80 70 - 80 70 - 80 68 - 75 70 - 78 70 - 81 72 - 81 70 - 81 220 220 220 220 220 100 100 100 100 100 current(ma) efficiency @fl(%) capacitor load(uf) xx=input voltage test configurations test configurations emi f ilt er input filte r components (c1, l ) are used to help meet conducted emissions requirement for the module. these components should be mounted as close as possible to the module; and all leads should be minimized to decrease radiated noise. , c2 , c3 dc/ dc converter + vout -vout + vin -vin c1 load l c1 l c2 c2 1210 , 2.2 uf/100v e lectrolytic capacitor , 10uf/100v 1210 , 2.2 uf/100v c3 1210 , 2.2 uf/100v c3 1206 , 470pf/2kv 1206 , 470pf/2kv 1210 , 2.2 uf/100v 1210 , 2.2 uf/100v 1210 , 2.2 uf/100v 1210 , 2.2 uf/100v rs7-05xxxxx rs7-12xxxxx rs7-15xxxxx rs7-24xxxxx rs7-48xxxxx rs7- 03xxxxx 18uh 18uh 18uh 18uh 18uh 18uh the information and specifications contained in this data sheet are believed to be correct at time of publication. however, motien technologies accepts no responsibility for consequences arising from printing errors or inaccuracies. specifications are subject to change without notice. no rights under any patent accompany the sale of any such product(s) or information contained herein. dc/dc-converter rs7-s10/d10 6.0w regulated single & dual output dc/dc-conerter 1.0w unregulated single & dual output we energie electronics an acal group copan we energie electronics &mfduspodpnpofoutnccsfoemohfs-etuc0ggfocdiccthfmfduspodef page 2 (3) stand juni 2016 rev 01 test configurations r s 7 - xx xx x xx power (w) input t ype a x code inter nal isolation (kvdc)
dc/dc-converter rs7-s10/d10 6.0w regulated single & dual output dc/dc-converter 1.0w unregulated single & dual output we energize electronics! an acal group company we energize electronics! rsg electronic components gmbh ? sprendlinger ldst. 115 ? 63069 offenbach ?+49 69-984047-0 ? rsg-electronic.de page 3 (5) stand juni 2016 rev 01 3 note 1.ripple/noise measured with 20mhz bandwidth. 2.tested by minimal vin and constant resistive load. 3.measured input reflected ripple current with a simulated source inductance of 12uh. 4.exceeding the absolute ratings of the unit could cause damage. it is not allowed for continuous operating. 5.operation under no-load conditions will not damage these devices, however they may not meet all listed specifications. 6 input filter components are be required to help meet conducted emission class b, 7. 8. for reduce converter s ripple & noise, it is recommended to add a 4.7 f~100 f( 4.7 f~ 68 f for dual output) capacitor in output end. for emi performance improvement, it is recommended to add a 12 h inductor and a 10 f~100 f capacitor in input end. . which application refer to the emi filter of design & feature configuration. an external filter capacitor is required if the m odule has to meet iec61000-4-4. t h e filter capacitor rsg suggest: nippon - chemi - con ky series, 470uf/100 v . vl - 1w unregulated single & dual output ??r?? ?gti 1 ?g ? + + gnd ci li single output current probe mechanical specifications motien last update : 01.apr.2013 no. 9, keji 2nd rd., tainan technology industrial park, tainan city 70955, taiwan te l: 886-6-384 2366 (rep.) fax: 886-6-384 2399 website : email : www.motien.com.tw sales@motien.com.tw iso 9001 . iso 14001 . iecq qc080000 approved: drawing: ??i??ii????i? ??ii???o p
? ? ? ??i??? ?e ?e ?e ?e ? e ? e ? e ? e ?nn ir?r ???? 7 pin sil package notes : all dimensions are typical in millimeters ( inches ). 1. pin diameter: 0.5 0.05 ( 0.02 0.002 ) 2. pin pitch and length tolerance: 0.35 ( 0.014 ) 3. case tolerance: 0.5 ( 0.02 ) 19. 50 (0.77) dc- dc converter rs7 -xxxxxxssh6 rsg 12.00 (0.47) 0.50 (0.02) 12 5 2.54 (0.10) 15.24 (0.60) 3.00 (0.12) 9.80 (0.39) printed face 7 12.50 (0.49) 6 9.80 (0.39) 0.50 (0.02) 0.25 (0.01) 0.50 (0.02) 2.40 (0.09) 2.13 (0.08) xxxx note mechanical specifications the models listed here are just standard type. if you need a product with special specifcaton or you have questons regarding packing standards (tube oder tape/reel) as well as applicaton support, please contact our specialists: sales @ rsg-electronic.de or +49 69-984047-41/-28
|
